Model: C200H-TM001.
Timing method: CR oscillator.
No. of timers: 4
Setting ranges: 0.1 to 1.0 s, 1 to 10 s, 10 to 60 s, 1 to 10 min
Operation: Controllable from PLC program. Usable as accumulating timer.
External adjustment: Via C4K-CN223 (2 m) connector to 20-I/O points: 256 pts.
Program capacity(words): 7 CP1E-E10DT1-D PROGRAMMING MANUAL. 2 K.
DM capacity (words): 6 K.
RS-232C port: YES.Name: Two-tier Screw Terminal Block CP1E-E10DT1-D
Specifications: Outputs; 16 outputs; NPN.
"Easy" and "Flexible" system expansion,
with linked CC-Link and CompoNet.
Branching is easily made with CompoNet.
Wiring material cost can be reduced.
Bit-level I/O distribution reduces,
wiring in the system.
A wide variety of CompoNet Slave Units,
contribute to system size reduction CP1E-E10DT1-D PROGRAMMING MANUAL.
Seven-segment Display on the Gateway Unit,
helps to detect errors on site.
The Participation Flags and Communications,
Error Flags can be checked at the Host,
Controller to detect the location and,
content of the error. For C200H-PRO27-E Hand-held Programming Console ming Console.
4m.CV500-RM SYSMAC BUS Remote I/O Master Unit Wired CV500-RM221.
Wire Type CP1E-E10DT1-D PROGRAMMING MANUAL. I/O Link of 8 input bits and 8 output bits Name: e-CON Connectors.
Specifications: Inputs; 8 inputs ; NPN;
Without Short-circuit and,
Disconnected Line Detection.
"Easy" and "Flexible" system expansion,
with linked CC-Link and CompoNet.
Branching is easily made with CompoNet.
Wiring material cost can be reduced.
Bit-level I/O distribution reduces,
wiring in the system.
A wide variety of CompoNet Slave Units,
contribute to system size reduction.
Seven-segment Display on the Gateway Unit,
helps to detect errors on site.
The Participation Flags and Communications,
Error Flags can be checked at the Host,
Controller to detect the location and,
content of the error. Unit type: CS1 Special I/O Units.
Product name: Isolated-type,
Thermocouple Input Units.
points Input: 4 inputs.
Signal range selection:
Set separately for each input.
I/O type: B, E, J, K, N, R, S, T, ±80mV.
Conversion speed: 150 ms/4 inputs.
Externa connection: Removable erminal block.
No. of unit numbers allocated: 1.
Current consumption: 5V, 0.15A; 26V, 0.15A.
Standards: UC1, CE.
Provides the functionality of isolators,
power supplies, signal converters,
and other devices.
The Analog Input Unit converts analog,
input signals such as 1 to 5 V or 4 to 20mA,
into digital values, and takes the values,
scaled in industrial units, and transfers,
it to the CPU Unit as the process value.
Because of this, no ladder program is required,
at the CPU Unit for scaling.
The Analog Output Unit converts analog output set,
values from the CPU Unit to analog output signals,
such as 4 to 20 mA or 1 to 5 V, and outputs them.
The built-in functions, such as measurement value,
alarms, rate-of-change calculations, and square roots,
have enabled major savings in cost and space comparedd,
with previous systems CP1E-E10DT1-D Hardware Manual.
High-resolution Models and 8-point Input Models are,
also available.
By combining the Units, logging/monitoring.
systems can be constructed,
or the Units can be used together with LCBs/LCCUs,
to construct complete process control systems CP1E-E10DT1-D Hardware Manual.
Parameters can be easily displayed and set in an,
easy-to-understand form without special tools.