Name: PID Control Module.
Model: C200H-PID03.
Output: Current output.CV500-FH SYSMAC BUS PC Unit Floppy/Hard Disk Drive For 100 VAC CV500-FHD01-EConnects Power Supply Adapter and SYSMAC NET Link Unit.
Included with C200H-APS01.Analog outputs : 2 points.
Power supply : built-in power supply
Ranges : -10 to + 10V or 0 to 20mACPU Unit: CP1H-XA CPU Units CPM2C-32CDTM-D SYSTEM MANUAL.
Specifications: CPU type, Memory capacity: 20K steps
High-speed counters: 100 kHz, 4 axes Pulse outputs:
100 kHz, 2 axes (Models with transistor outputs only);
Analog inputs: 4, Analog outputs: 2;
Power supply, AC power supply; Output method, Relay output;
Inputs, 24; Output, 16 CPM2C-32CDTM-D
Standards: UC1, N, L, CE.
4 Axis Position Control and Comprehensive Programmable Controller CPM2C-32CDTM-D SYSTEM MANUAL.
The CP1H-X with pulse outputs for 4 axes.
The CP1H-Y with 1-MHz pulse I/O.
The CP1H-XA with pulse outputs for 4 axes and built-in analog I/O. Product: DeviceNet Unit.
Specifications: For CS Series,
Functions as either a master or a slave.
2,048 I/O points.
Standards: UC1, N, L, CE.
A DeviceNet Unit for the CS Series.
That Boasts Industry-leading CPM2C-32CDTM-D SYSTEM MANUAL.
Performance and Functions. Name: Temperature Input Units.
Specifications: Platinum-resistance,
thermometer input; 4 inputs;
PT100 (-200 to 850°C),
PT100 (-200 to 2000°C).
Standards: CE, UC, UC1, N .
"Easy" and "Flexible" system expansion,
with linked CC-Link and CompoNet.
Branching is easily made with CompoNet.
Wiring material cost can be reduced.
Bit-level I/O distribution reduces,
wiring in the system.
A wide variety of CompoNet Slave Units,
contribute to system size reduction.
Seven-segment Display on the Gateway Unit,
helps to detect errors on site.
The Participation Flags and Communications,
Error Flags can be checked at the Host,
Controller to detect the location and,
content of the error. Unit type: CS1 Special I/O Units.
Product name: Power Transducer Input Unit.
Input points : 8 inputs.
Signal range: 0 to 1 mA, ±1 mA.
Conversion speed (resolution):
200ms/8 inputs.
Externa connection: Removable erminal block.
No. of unit numbers allocated: 1.
Current consumption: 5V, 0.15A; 26V, 0.08A.
Standards: UC1, CE.
Provides the functionality of isolators,
power supplies, signal converters,
and other devices.
The Analog Input Unit converts analog,
input signals such as 1 to 5 V or 4 to 20mA,
into digital values, and takes the values,
scaled in industrial units, and transfers,
it to the CPU Unit as the process value.
Because of this, no ladder program is required,
at the CPU Unit for scaling.
The Analog Output Unit converts analog output set,
values from the CPU Unit to analog output signals,
such as 4 to 20 mA or 1 to 5 V, and outputs them.
The built-in functions, such as measurement value,
alarms, rate-of-change calculations, and square roots,
have enabled major savings in cost and space ccompared,
with previous systems CPM2C-32CDTM-D Manual.
High-resolution Models and 8-point Input Models are,
also available.
By combining the Units, logging/monitoring.
systems can be constructed,
or the Units can be used together with LCBs/LCCUs,
to construct complete process control systems CPM2C-32CDTM-D Manual.
Parameters can be easily displayed and set in an,
easy-to-understand form without special tools.