Appearance: Unshielded.
Sensing surface: Front.
Sensing distance: 1.6 mm.
Output configuration: PNP.
Model: Operation mode, NC.
Advanced Performance and Wide.
Range of Selections in a Super.
compact Size.
Only 5.5 × 5.5 mm with a built-in Amplifier.
Maximum sensing distance: 2.5 mm. Stable detection even with,
workpiece fluctuations E5AC-TQX4DSM-060 Instructions Manual.
Response frequency: 1 kHz E5AC-TQX4DSM-060
Low current consumption. Appearance: Unshielded, M18.
Sensing distance: 8 mm.
Output configuration: AC 2-wire.
Model: Operation mode, NO.
General-purpose Threaded.
Capacitive Sensor.
Product lineup with M12, M18, and M30 models.
Fixed sensing distance requires no sensitivity adjustment. Appearance: Close mounting.
Sensing method: Throughbeam type(with slot) E5AC-TQX4DSM-060 Instructions Manual.
Connecting method: Connector(4 poles).
Sensing distance: 5 mm (slot width).
Output configuration: Dark-ON/Light-ON (selectable).
Indicator mode: No incident light.
Model: NPN output.
Global Standard Slot-type.
photomicrosensors with 50- to,
100-mA direct switching capacity.
Series includes models that enable switching between,
dark-ON and light-ON operation E5AC-TQX4DSM-060 Instructions Manual.
Response frequency as high as 1 kHz.
Easy operation monitoring with bright light indicator.
Wide operating voltage range: 5 to 24 VDC.
Models in which the light indicator turns ON for dark-ON,
operation are also available.
A wide range of variations in eight different shapes.
Flexible robot cable is provided as a standard feature. High performance price ratio standard type proximity sensor.
Standard cable protector.
The new DC two-wire type.
Non polar proximity sensor.
Type: DC three wire / wire type.
Shape: shield, M12.
Detection range: 2mm.
Output configuration: PNP.
Action mode: NO. E32-D33 type: special beam type; ultra small / small diameter beam,
Specialty: Phi 0.8 casing,
Bending radius (mm): R4.
Standard test object (minimum test object) (mm) 1: (0.005),
Fiber element for meeting diversified needsSize: 48 x 96mm.
Category: power AC100 ~ 240V with.
Shell color: black.
Control output 1: output unit mode.
Control output 2: output unit mode.
Control mode: standard or heating cooling.
Auxiliary output points: 2 points.
Heater break, SSR fault detection function: single phase or three phase heater detection function.
Event entry point: 2.
Transfer output: transfer output (special terminal).
Remote SP:4 to 20mA input.
Communication: -.
New program type.
A new type of liquid crystal with high performance cost ratio is adopted in the 256 paragraph,
Visual angle, contrast can be improved.
Can be set up to 8 procedures (mode) x 32 (step) procedure.
High resolution 5 bit display / can display 0.01 degrees C.
High speed sampling period 60ms.
All models complete a variety of (to the thermocouple /Pt/ analog input switching), 1 machines to support a variety of sensors.
Also supports remote SP.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/RESET, alarm), interactive display PV/SV.
Through the support software (Ver.4.3 CX-Thermo) makes the process of seetting management becomes very
Simple use of simple computing functions (AND/OR logic and delay) to set the implementation of flexible contact output E5AC-TQX4DSM-060 RS-485 CompoWay/F Manual.
Through the infrared port can be carried out from the frront of the communication E5AC-TQX4DSM-060 RS-485 CompoWay/F Manual.
The control output ON/OFF times counting function can predict the fault of the internal relay of the temperature controller.