LK Automation Limited LK Automation Limited
Download Sort: OMRON
Home >> Manual Download
OMRON K3HB-HTA-L1AT11 Manual K3HB-HTA-L1AT11 Communications Manual
Product model: K3HB-HTA-L1AT11
Name: Digital Temperature Controllers
Brand: OMRON
Sort: Communications Manual
File language: English
Time specification: Inverse type.
Current setting range: 2 to 8 A.
Operating voltage: 200/220/240 VAC.
Resetting method: Automatic (See note.).
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage K3HB-HTA-L1AT11 Communications Manual.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase K3HB-HTA-L1AT11
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked easily because operation time,
is indicated from the start of operation.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, and load conditions K3HB-HTA-L1AT11 Communications Manual. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM. Input type: DC voltage input type.
Output type: linear; current; NPN open collector (HH, H, PASS, L, LL).
Event input terminal 5 points (TIMING, S-TIM, HOLD, RESET, ZERO) is equipped with K3HB-HTA-L1AT11 Communications Manual.
External supply 80mA DC12V.
Power supply voltage: AC/DC24V.
96 (W) * 48 (H * 95mm) depth
Some models are not equipped with.
The most suitable voltage and current signal simulation, measurement and display, identification of the panel table.
Action determine the color, can switch the green / Red 2 kinds of color display.
Equipped with the sub pressure gauge for monitoring the operation trend.
External event input can be applied to a variety of measurement and identification situations.
DeviceNet typeRated primary current: 50 A.
Rated secondary current: Special output.
Installation: Installed separately.
High-performance Power Monitor Suitable for On-panel Mounting and Display.
Assists Energy-saving Analysis.
Energy classification for wasted standby and stopped power.
(Classification based on external inputs is also supported.)
Power and current can be measured simultaneously.
Measurement of flow rates with a pulse conversion function.
Simple temperature measurements with Temperature Sensor included in the Unit.
High-precision Measurements.
Measurement of generated power (regenerative power),
leading reactive power, lagging reactive power, and consumed power.
Power measurements on the primary side of inverters,
which are widely used to save energy.
Automatic range switching for accurate measurement of standby and stopped power.
Energy-saving Functions.
Conversion to monetary cost. (Also used for classified standby and stopped power.)
Allarm outputs can be selected for active power, reactive power,
regenerative power, current, voltage, or power factor K3HB-HTA-L1AT11 Manual.
The Power Monitor can log measurement data and supports Modbus communications.
Installation and Settingss K3HB-HTA-L1AT11 Manual.
Direct measurement of three-phase, four-wire, 400-V line voltage.
Simple measurements without voltage wiring.
Incorrect voltage wiring detection.
Related products
OMRON
Temperature panel
K3HB-HTA-L2AT11 AC/DC24
OMRON Temperature panel K3HB-HTA-L2AT11 AC/DC24
Type of input: platinum resistance / the
OMRON
Time interval table
K3HB-PPB-L1AT11 AC/DC24V
OMRON Time interval table K3HB-PPB-L1AT11 AC/DC24V
Input type: PNP input type. Event input
OMRON
Rotating pulse meter
K3HB-RPB-L1AT11 AC100-240
OMRON Rotating pulse meter K3HB-RPB-L1AT11 AC100-240
Input type: PNP input type. Event input
OMRON
Temperature panel
K3HB-HTA-1 AC100-240
OMRON Temperature panel K3HB-HTA-1 AC100-240
Type of input: platinum resistance / the