LK Automation Limited
Brand:
OMRON
S8JT Series | OMRON Switching Mode Power Supply S8JT Series
OMRON S8JT Series Product information and technical parameters：
Brand: OMRON
Name: Switching Mode Power Supply
Model: S8JT Series
Compact and economical switching power supply, capacity up to 150W
Type: Cable with Connectors on Both Ends (RJ45/RJ45).
Category: Cat.6a .
Cable sheath material: LSZH.
Cable color: Yellow.
Cable length: 20 m.
Cables and Connectors for,
EtherCAT® and Other Industrial,
Ethernet Networks. Type: collection type.
Shell: square body embedded type.
30 years of best-selling products new upgrade in the reservation,
Based on the basic functions to achieve a compact OMRON S8JT Series S8JT Series
The installation dimensions of the surface type remain unchanged, the volume ratio of the volume ratio of the square body is reduced,
Half. (excluding AGD-U2)
Built in digital filter to reduce the impact of high frequency interference, to achieve a higher accuracy,
Leakage monitoring.
The output point consists of 1c1a * monitoring circuit, an external signal based on contact,
Remote monitoring and alarm output of each monitoring circuit OMRON S8JT Series.
Cube embedded type also built-in buzzer. (except AGD-U2) alarm output,
Optional external buzzer.
After the upgrade of all products can choose automatic reset, manual reset.
(AGD-N5, AGD-NY5, AGD-N52)Time specification: Inverse type.
Current setting range: 20 to 65 A OMRON S8JT Series.
Operating voltage: 200/220/240 VAC.
Resetting method: Automatic (See note.).
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase.
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked easily because operation time,
is iindicated from the start of operation S8JT Series.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, and load conditions S8JT Series. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM.
Category: Cat.6a .
Cable sheath material: LSZH.
Cable color: Yellow.
Cable length: 20 m.
Cables and Connectors for,
EtherCAT® and Other Industrial,
Ethernet Networks. Type: collection type.
Shell: square body embedded type.
30 years of best-selling products new upgrade in the reservation,
Based on the basic functions to achieve a compact OMRON S8JT Series S8JT Series
The installation dimensions of the surface type remain unchanged, the volume ratio of the volume ratio of the square body is reduced,
Half. (excluding AGD-U2)
Built in digital filter to reduce the impact of high frequency interference, to achieve a higher accuracy,
Leakage monitoring.
The output point consists of 1c1a * monitoring circuit, an external signal based on contact,
Remote monitoring and alarm output of each monitoring circuit OMRON S8JT Series.
Cube embedded type also built-in buzzer. (except AGD-U2) alarm output,
Optional external buzzer.
After the upgrade of all products can choose automatic reset, manual reset.
(AGD-N5, AGD-NY5, AGD-N52)Time specification: Inverse type.
Current setting range: 20 to 65 A OMRON S8JT Series.
Operating voltage: 200/220/240 VAC.
Resetting method: Automatic (See note.).
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase.
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked easily because operation time,
is iindicated from the start of operation S8JT Series.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, and load conditions S8JT Series. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM.
...More relevant models >>>>