LK Automation Limited
Brand:
OMRON
XS3F-M421-402-A | OMRON Round Water-resistant Connectors XS3F-M421-402-A
OMRON XS3F-M421-402-A Manual And Instructions
XS3F-M421-402-A datasheetPDF datasheet
OMRON XS3F-M421-402-A Product information and technical parameters：
Brand: OMRON
Name: Round Water-resistant Connectors
Model: XS3F-M421-402-A
No. of cable cores: 4.
Item: Standard cable.
Cable connection direction: Straight.
Cable length L: 2 m.
Small Round Water-resistive.
Connectors.
Water-resistive, compact connector meets IP67 requirements.
Conventional M8 screw-mounting models are available along with,
S8 snap-in models that connect and disconnect with one touch.
Ideal for a wide variety of FA and OA applications.
Connectors on both cable ends require no harness work.
Some new M8 models with 3 or 5 poles.
...More relevant models >>>>
XS3F-M421-402-A datasheetPDF datasheet
OMRON XS3F-M421-402-A Product information and technical parameters：
Brand: OMRON
Name: Round Water-resistant Connectors
Model: XS3F-M421-402-A
No. of cable cores: 4.
Item: Standard cable.
Cable connection direction: Straight.
Cable length L: 2 m.
Small Round Water-resistive.
Connectors.
Water-resistive, compact connector meets IP67 requirements.
Conventional M8 screw-mounting models are available along with,
S8 snap-in models that connect and disconnect with one touch.
Ideal for a wide variety of FA and OA applications.
Connectors on both cable ends require no harness work.
Some new M8 models with 3 or 5 poles.
Sensor type and wiring: 3-wire DC PNP/2-wire DC 1-4.
Actuator wiring: Actuator wiring 3-4.
No. of ports: 8.
No. of I/O: 8.
Simple Wiring of Sensor Actuators.
Greatly reduce wiring in combination with the Smartclick XS5.
Insert the connector and turn 1/8 of a turn to lock the connectors.
Higher rated current to enable output applications OMRON XS3F-M421-402-A.
Use previous M12 screw connectors XS3F-M421-402-A Cable /G79-Y_C with loose wire connecting terminal.
L size: 3000mm.
Cable and loose wire cable with loose wire pressing connecting terminal,
Connector cable, MITSUBISHI motor produced PLC connection cable. Terminals: Push-In Plus terminal blocks.
Type: Input *1.
Points: 16.
Internal I/O circuit common: PNP (+ common) OMRON XS3F-M421-402-A.
Rated voltage: 24 VDC.
I/O Relay Terminals with 16 Points and,
Push-In Plus terminal blocks to,
Downsize Control Panels and Save Labor.
I/O Relay Terminals with 16 points to mount G2RV Slim I/O Relays.
Push-In Plus terminal blocks are used to save wiring work in,
comparison with traditional screw terminals. (Wiring time is,
reduced by 60%* in comparison with traditional screw terminals OMRON XS3F-M421-402-A. ).
Work is reduced ever further with one-step cable connection to the PLC.
Diode provided for coil surge absorption.
Operation indicators for immediate recognition of I/O signal status.
Accepts G3RV Slim I/O SSRs.
DIN Track or screw mounting. Servo trunk unit.
Product Name: servo relay unit.
Application unit: CS1W/CJ1W/C200HW-NC__3, C200H-NC.
Specifications: -.
Axis number: biaxial.
The connector and terminal of the relay unit are integrated into a whole,
Save the wiring servo drive and position control unit.
Servo driver and control signal of position control unit,
Simple wiring on terminal stage XS3F-M421-402-A.
The connector without soldering, with only a screwdriver can wiring.
Dedicated connection cable between units.
DIN guide rail installation, the rapid installaation, screw installation of two methods XS3F-M421-402-A.
M3.0 thread terminals attached with a special plate signal.
The terminal can be confirmed by the signal name.
Actuator wiring: Actuator wiring 3-4.
No. of ports: 8.
No. of I/O: 8.
Simple Wiring of Sensor Actuators.
Greatly reduce wiring in combination with the Smartclick XS5.
Insert the connector and turn 1/8 of a turn to lock the connectors.
Higher rated current to enable output applications OMRON XS3F-M421-402-A.
Use previous M12 screw connectors XS3F-M421-402-A Cable /G79-Y_C with loose wire connecting terminal.
L size: 3000mm.
Cable and loose wire cable with loose wire pressing connecting terminal,
Connector cable, MITSUBISHI motor produced PLC connection cable. Terminals: Push-In Plus terminal blocks.
Type: Input *1.
Points: 16.
Internal I/O circuit common: PNP (+ common) OMRON XS3F-M421-402-A.
Rated voltage: 24 VDC.
I/O Relay Terminals with 16 Points and,
Push-In Plus terminal blocks to,
Downsize Control Panels and Save Labor.
I/O Relay Terminals with 16 points to mount G2RV Slim I/O Relays.
Push-In Plus terminal blocks are used to save wiring work in,
comparison with traditional screw terminals. (Wiring time is,
reduced by 60%* in comparison with traditional screw terminals OMRON XS3F-M421-402-A. ).
Work is reduced ever further with one-step cable connection to the PLC.
Diode provided for coil surge absorption.
Operation indicators for immediate recognition of I/O signal status.
Accepts G3RV Slim I/O SSRs.
DIN Track or screw mounting. Servo trunk unit.
Product Name: servo relay unit.
Application unit: CS1W/CJ1W/C200HW-NC__3, C200H-NC.
Specifications: -.
Axis number: biaxial.
The connector and terminal of the relay unit are integrated into a whole,
Save the wiring servo drive and position control unit.
Servo driver and control signal of position control unit,
Simple wiring on terminal stage XS3F-M421-402-A.
The connector without soldering, with only a screwdriver can wiring.
Dedicated connection cable between units.
DIN guide rail installation, the rapid installaation, screw installation of two methods XS3F-M421-402-A.
M3.0 thread terminals attached with a special plate signal.
The terminal can be confirmed by the signal name.
...More relevant models >>>>